1
Which of the following is considered a limitation of RIP v1?
*** RIP v1 does not send subnet mask information in its updates.
RIP v1 is not widely supported by networking hardware vendors.
RIP v1 consumes excessive bandwidth by multicasting routing updates using a Class D address.
RIP v1 requires enhanced router processors and extra RAM to function effectively.
RIP v1 does not support load balancing across equal-cost paths.
RIP v1 authentication is complicated and time-consuming to configure.
2
The subnet 192.168.32.16/28 has been selected to be further subnetted to support point-to-point serial links. What is the maximum number of serial links that this plan can support?
2
3
3 if ip subnet-zero is enabled
*** 4
6
8
3
What is the default network mask for a Class B address?
255.0.0.0
*** 255.255.0.0
255.255.255.0
255.255.255.255
4
A new network is to be configured on a router. Which of the following tasks must be completed to configure this interface and implement dynamic IP routing for the new network? (Choose three.)
*** Select the routing protocol to be configured.
*** Assign an IP address and subnet mask to the interface.
Update the ip host configuration information with the device name and new interface IP address.
*** Configure the routing protocol with the new network IP address.
Configure the routing protocol with the new interface IP address and subnet mask.
Configure the routing protocol in use on all other enterprise routers with the new network information.
5
Which command must the administrator execute to disable the capability to use subnets that include the network address of the unsubnetted network?
Router(config)# no ip classless
Router(config)# no ip zero subnet
*** Router(config)# no ip subnet-zero
Router(config)# no ip zero-subnet
Router(config)# no subnet-zero
6
Which of the following problems does VLSM help to alleviate?
*** the shortage of IP addresses
the difficulty of assigning static IP addresses to hosts in large enterprises
the complexity of implementing advanced routing protocols such as OSPF and EIGRP
the shortage of network administrators qualified in the use of RIP v1 and IGRP
7
Which of the following are contained in the routing updates of classless routing protocols? (Choose two.)
*** 32-bit address
next hop router interface
*** subnet mask
unicast host address
Layer 2 address
8
An additional subnet is required for a new Ethernet link between Router1 and Router2 as shown in the diagram. Which of the following subnet addresses can be configured in this network to provide a maximum of 14 useable addresses for this link while wasting the fewest addresses?
192.1.1.16/26
192.1.1.96/28
192.1.1.160/28
192.1.1.196/27
*** 192.1.1.224/28
192.1.1.240/28
9
How often does RIP v1 send routing table updates, by default?
*** every 30 seconds
every 45 seconds
every 60 seconds
every 90 seconds
10
What does VLSM allow a network administrator to do?
utilize one subnet mask throughout an autonomous system
*** utilize multiple subnet masks in the same IP address space
utilize IGRP as the routing protocol in an entire autonomous system
utilize multiple routing protocols within an autonomous system
11
Which subnet mask is represented by the /21 notation?
255.255.224.0
*** 255.255.248.0
255.255.252.0
255.255.240.0
12
Router1 and Router2 shown in the topology have been configured with the no ip subnet-zero command. Which of the following valid VLSM network numbers could be used for the serial link between Router1 and Router2? (Choose two.)
192.168.1.0/30
*** 192.168.1.4/30
*** 192.168.1.8/30
192.168.1.96/30
192.168.1.138/30
192.168.1.190/30
13
A Class C network address has been subnetted into eight subnetworks. Using VLSM, the last subnet will be divided into eight smaller subnetworks. What bit mask must be used to create eight smaller subnetworks, each having two usable host addresses?
/26
/27
/28
/29
*** /30
/31
14
The routers in the diagram use the subnet assignments shown. What is the most efficient route summary that can be configured on Router3 to advertise the internal networks to the cloud?
192.1.1.0/26 and 192.1.1.64/27
192.1.1.128/25
192.1.1.0/23 and 192.1.1.64/23
192.1.1.0/24
*** 192.1.1.0/25
192.1.1.0/24 and 192.1.1.64/24
15
How does a router know of paths to destination networks? (Choose two.)
inspection of the destination IP address in data packets
ARP requests from connected routers
*** manual configuration of routes
*** updates from other routers
DHCP information broadcasts
updates from the SMTP management information base
16
The network shown in the diagram is having problems routing traffic. It is suspected that the problem is with the addressing scheme. What is the problem with the addressing used in the topology?
The address assigned to the Ethernet0 interface of Router1 is a broadcast address for that subnetwork.
*** The subnetwork configured on the serial link between Router1 and Router2 overlaps with the subnetwork assigned to Ethernet0 of Router3.
The subnetwork assigned to the Serial0 interface of Router1 is on a different subnetwork from the address for Serial0 of Router2.
The subnetwork assigned to Ethernet0 of Router2 overlaps with the subnetwork assigned to Ethernet0 of Router3.
17
A Class C address has been assigned for use in the network shown in the graphic. Using VLSM, which bit mask should be used to provide for the number of host addresses required on Router A, while wasting the fewest addresses?
/31
/30
/29
/28
*** /27
/26
18
Which command would a network administrator use to determine if the routers in an enterprise have learned about a newly added network?
router# show ip address
*** router# show ip route
router# show ip networks
router# show ip interface brief
router# debug ip protocol
router# debug rip update
19
Refer to the network shown. How will Router1 summarize and advertise the four networks attached to its Ethernet ports?
172.16.16.0/20
172.16.19.0/20
172.16.16.0/20 and 172.16.19.0/20
*** 172.16.16.0/22
172.16.18.0/24
172.16.0.0/24
20
In the network shown in the graphic, three bits were borrowed from the host portion of a Class C address. How many valid host addresses will be unused on the three point-to-point links combined if VLSM is not used?
3
4
12
36
*** 84
180
21
Which of the following statements are true regarding RIP v1 and v2? (Choose three.)
*** Both RIP versions use hop count.
Both RIP versions can provide authentication of update sources.
*** Both RIP versions use 16 hops as a metric for infinite distance.
RIP v1 uses split horizon to prevent routing loops while RIP v2 does not.
RIP v1 uses hold-down times to prevent routing loops while RIP v2 does not.
*** RIP v1 broadcasts routing table updates, while RIP v2 multicasts its updates.
22
What is the purpose of the network command used in the configuration of the RIP routing protocol?
It specifies RIP v2 as the routing protocol.
It enables the use of VLSM.
It specifies the fastest path to the destination route.
It specifies which interfaces will exchange RIP routing updates.
*** It activates RIP for all routes that exist within the enterprise network.
23
Refer to the graphic. Which command will enter a static route to network 192.168.19.0 from router C?
C(config)# ip route 192.168.19.0 192.168.17.1
C(config)# ip static-route 192.168.19.0/24 192.168.17.2
C(config)# ip route 192.168.17.1 255.255.255.0 192.168.19.0
*** C(config)# ip route 192.168.19.0 255.255.255.0 192.168.17.1
C(config)# ip route 192.168.19.0 0.0.0.0 192.168.17.2
C(config)# ip default-route 192.168.17.2 255.255.255.0 192.168.19.0
Kaynak: Cisco Curr v3.1
belgesi-1256
0 kişi bu belgeyi faydalı buldu
0 kişi bu belgeyi faydalı buldu
